In the Linux kernel, the following vulnerability has been resolved:
soc/tegra: cbb: Fix cross-fabric target timeout lookup
When a fabric receives an error interrupt, the error may have
occurred on a different fabric. The target timeout lookup was using
the wrong base address (cbb->regs) with offsets from a different
fabric's target map, causing a kernel page fault.
Unable to handle kernel paging request at virtual address ffff80000954cc00
pc : tegra234_cbb_get_tmo_slv+0xc/0x28
Call trace:
tegra234_cbb_get_tmo_slv+0xc/0x28
print_err_notifier+0x6c0/0x7d0
tegra234_cbb_isr+0xe4/0x1b4
Add tegra234_cbb_get_fabric() to look up the correct fabric device
using fab_id, and use its base address for accessing target timeout
registers.
In the Linux kernel, the following vulnerability has been resolved:
ocfs2/dlm: fix off-by-one in dlm_match_regions() region comparison
The local-vs-remote region comparison loop uses '<=' instead of '<',
causing it to read one entry past the valid range of qr_regions. The
other loops in the same function correctly use '<'.
Fix the loop condition to use '<' for consistency and correctness.
In the Linux kernel, the following vulnerability has been resolved:
power: supply: max77705: Free allocated workqueue and fix removal order
Use devm interface for allocating workqueue to fix two bugs at the same
time:
1. Driver leaks the memory on remove(), because the workqueue is not
destroyed.
2. Driver allocates workqueue and then registers interrupt handlers
with devm interface. This means that probe error paths will not use a
reversed order, but first destroy the workqueue and then, via devm
release handlers, free the interrupt.
The interrupt handler schedules work on this exact workqueue, thus if
interrupt is hit in this short time window - after destroying
workqueue, but before devm() frees the interrupt - the schedulled
work will lead to use of freed memory.
Change is not equivalent in the workqueue itself: use non-legacy API
which does not set (__WQ_LEGACY | WQ_MEM_RECLAIM). The workqueue is
used to update power supply (power_supply_changed()) status, thus there
is no point to run it for memory reclaim. Note that dev_name() is not
directly used in second argument to prevent possible unlikely parsing
any "%" character in device name as format.
In the Linux kernel, the following vulnerability has been resolved:
pinctrl: pinconf-generic: Fully validate 'pinmux' property
The pinconf_generic_parse_dt_pinmux() assumes that the 'pinmux' property
is not empty when present. This might be not true. With that, the allocator
will give a special value in return and not NULL which lead to the crash
when trying to access that (invalid) memory. Fix that by fully validating
'pinmux' value, including its length.
In the Linux kernel, the following vulnerability has been resolved:
tty: hvc_iucv: fix off-by-one in number of supported devices
MAX_HVC_IUCV_LINES == HVC_ALLOC_TTY_ADAPTERS == 8.
This is the number of entries in:
static struct hvc_iucv_private *hvc_iucv_table[MAX_HVC_IUCV_LINES];
Sometimes hvc_iucv_table[] is limited by:
(a) if (num > hvc_iucv_devices) // for error detection
or
(b) for (i = 0; i < hvc_iucv_devices; i++) // in 2 places
(so these 2 don't agree; second one appears to be correct to me.)
hvc_iucv_devices can be 0..8. This is a counter.
(c) if (hvc_iucv_devices > MAX_HVC_IUCV_LINES)
If hvc_iucv_devices == 8, (a) allows the code to access hvc_iucv_table[8].
Oops.
In the Linux kernel, the following vulnerability has been resolved:
usb: typec: ps883x: Fix Oops at unbind
When trying to unbind a device in order to bind to it vfio-platform as:
echo bc0000.geniqup > /sys/bus/platform/devices/bc0000.geniqup/driver/unbind
I get the following Oops:
[ 436.478639] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
[ 436.487762] Mem abort info:
[ 436.490716] ESR = 0x0000000096000004
[ 436.494595] EC = 0x25: DABT (current EL), IL = 32 bits
[ 436.500071] SET = 0, FnV = 0
[ 436.503250] EA = 0, S1PTW = 0
[ 436.506505] FSC = 0x04: level 0 translation fault
[ 436.511533] Data abort info:
[ 436.514558] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
[ 436.520215] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 436.525436] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 436.530918] user pgtable: 4k pages, 48-bit VAs, pgdp=00000008861a9000
[ 436.537554] [0000000000000020] pgd=0000000000000000, p4d=0000000000000000
[ 436.544548] Internal error: Oops: 0000000096000004 [#1] SMP
[ 436.550374] Modules linked in:
[ 436.553542] CPU: 2 UID: 0 PID: 671 Comm: bash Tainted: G W 7.0.0-rc3-g56fcdd0911a5-dirty #2 PREEMPT
[ 436.564440] Tainted: [W]=WARN
[ 436.567515] Hardware name: LENOVO 91B6CTO1WW/3796, BIOS O6NKT3BA 05/02/2025
[ 436.574675] pstate: 21400005 (nzCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
[ 436.581841] pc : ps883x_retimer_remove+0x14/0x94
[ 436.586605] lr : i2c_device_remove+0x28/0x84
[ 436.591017] sp : ffff8000847137c0
That's because the ps883x_retimer_remove() retrieves the driver data
from i2c_get_clientdata() which was never set at probe. So, add
i2c_set_clientdata() at the end of the probe.
In the Linux kernel, the following vulnerability has been resolved:
scsi: sg: Resolve soft lockup issue when opening /dev/sgX
The parameter def_reserved_size defines the default buffer size reserved
for each Sg_fd and should be restricted to a range between 0 and 1,048,576
(see https://tldp.org/HOWTO/SCSI-Generic-HOWTO/proc.html). Although the
function sg_proc_write_dressz enforces this limit, it is possible to bypass
it by directly modifying the module parameter as shown below, which then
causes a soft lockup:
echo -1 > /sys/module/sg/parameters/def_reserved_size
exec 4<> /dev/sg0
watchdog: BUG: soft lockup - CPU#5 stuck for 26 seconds! [bash:537]
Modules loaded:
CPU: 5 UID: 0 PID: 537 Command: bash, kernel version 6.19.0-rc3+ #134,
PREEMPT disabled
Hardware: QEMU Standard PC (i440FX + PIIX, 1996), BIOS version
1.16.1-2.fc37 dated 04/01/2014
...
Call Trace:
sg_build_reserve+0x5c/0xa0
sg_add_sfp+0x168/0x270
sg_open+0x16e/0x340
chrdev_open+0xbe/0x230
do_dentry_open+0x175/0x480
vfs_open+0x34/0xf0
do_open+0x265/0x3d0
path_openat+0x110/0x290
do_filp_open+0xc3/0x170
do_sys_openat2+0x71/0xe0
__x64_sys_openat+0x6d/0xa0
do_syscall_64+0x62/0x310
entry_SYSCALL_64_after_hwframe+0x76/0x7e
The fix is to use module_param_cb to validate and reject invalid values
assigned to def_reserved_size.
In the Linux kernel, the following vulnerability has been resolved:
f2fs: protect extension_list reading with sb_lock in f2fs_sbi_show()
In f2fs_sbi_show(), the extension_list, extension_count and
hot_ext_count are read without holding sbi->sb_lock. If a concurrent
sysfs store modifies the extension list via f2fs_update_extension_list(),
the show path may read inconsistent count and array contents, potentially
leading to out-of-bounds access or displaying stale data.
Fix this by holding sb_lock around the entire extension list read
and format operation.
In the Linux kernel, the following vulnerability has been resolved:
crypto: eip93 - fix hmac setkey algo selection
eip93_hmac_setkey() allocates a temporary ahash transform for
computing HMAC ipad/opad key material. The allocation uses the
driver-specific cra_driver_name (e.g. "sha256-eip93") but passes
CRYPTO_ALG_ASYNC as the mask, which excludes async algorithms.
Since the EIP93 hash algorithms are the only ones registered
under those driver names and they are inherently async, the
lookup is self-contradictory and always fails with -ENOENT.
When called from the AEAD setkey path, this failure leaves the
SA record partially initialized with zeroed digest fields. A
subsequent crypto operation then dereferences a NULL pointer in
the request context, resulting in a kernel panic:
```
pc : eip93_aead_handle_result+0xc8c/0x1240 [crypto_hw_eip93]
lr : eip93_aead_handle_result+0xbec/0x1240 [crypto_hw_eip93]
sp : ffffffc082feb820
x29: ffffffc082feb820 x28: ffffff8011043980 x27: 0000000000000000
x26: 0000000000000000 x25: ffffffc078da0bc8 x24: 0000000091043980
x23: ffffff8004d59e50 x22: ffffff8004d59410 x21: ffffff8004d593c0
x20: ffffff8004d593c0 x19: ffffff8004d4f300 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000007fda7aa498
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: fffffffff8127a80 x9 : 0000000000000000
x8 : ffffff8004d4f380 x7 : 0000000000000000 x6 : 000000000000003f
x5 : 0000000000000040 x4 : 0000000000000008 x3 : 0000000000000009
x2 : 0000000000000008 x1 : 0000000028000003 x0 : ffffff8004d388c0
Code: 910142b6 f94012e0 f9002aa0 f90006d3 (f9400740)
```
The reported symbol eip93_aead_handle_result+0xc8c is a
resolution artifact from static functions being merged under
the nearest exported symbol. Decoding the faulting sequence:
```
910142b6 ADD X22, X21, #0x50
f94012e0 LDR X0, [X23, #0x20]
f9002aa0 STR X0, [X21, #0x50]
f90006d3 STR X19, [X22, #0x8]
f9400740 LDR X0, [X26, #0x8]
```
The faulting LDR at [X26, #0x8] is loading ctx->flags
(offset 8 in eip93_hash_ctx), where ctx has been resolved
to NULL from a partially initialized or unreachable
transform context following the failed setkey.
Fix this by dropping the CRYPTO_ALG_ASYNC mask from the
crypto_alloc_ahash() call. The code already handles async
completion correctly via crypto_wait_req(), so there is no
requirement to restrict the lookup to synchronous algorithms.
Note that hashing a single 64-byte block through the hardware
is likely slower than doing it in software due to the DMA
round-trip overhead, but offloading it may still spare CPU
cycles on the slower embedded cores where this IP is found.
[Detailed investigation report of this bug]
In the Linux kernel, the following vulnerability has been resolved:
reset: amlogic: t7: Fix null reset ops
Fix missing reset ops causing kernel null pointer dereference.
This SOC's reset is currently not used yet.
In the Linux kernel, the following vulnerability has been resolved:
net: enetc: fix NTMP DMA use-after-free issue
The AI-generated review reported a potential DMA use-after-free issue
[1]. If netc_xmit_ntmp_cmd() times out and returns an error, the pending
command is not explicitly aborted, while ntmp_free_data_mem()
unconditionally frees the DMA buffer. If the buffer has already been
reallocated elsewhere, this may lead to silent memory corruption. Because
the hardware eventually processes the pending command and perform a DMA
write of the response to the physical address of the freed buffer.
To resolve this issue, this patch does the following modifications:
1. Convert cbdr->ring_lock from a spinlock to a mutex
The lock was originally a spinlock in case NTMP operations might be
invoked from atomic context. After downstream support for all NTMP
tables, no such usage has materialized. A mutex lock is now required
because the driver now needs to reclaim used BDs and release associated
DMA memory within the lock's context, while dma_free_coherent() might
sleep.
2. Introduce software command BD (struct netc_swcbd)
The hardware write-back overwrites the addr and len fields of the BD,
so the driver cannot rely on the hardware BD to free the associated DMA
memory. The driver now maintains a software shadow BD storing the DMA
buffer pointer, DMA address, and size. And netc_xmit_ntmp_cmd() only
reclaims older BDs when the number of used BDs reaches
NETC_CBDR_CLEAN_WORK (16). The software BD enables correct DMA memory
release. With this, struct ntmp_dma_buf and ntmp_free_data_mem() are no
longer needed and are removed.
3. Require callers to hold ring_lock across netc_xmit_ntmp_cmd()
netc_xmit_ntmp_cmd() releases the ring_lock before the caller finishes
consuming the response. At this point, if a concurrent thread submits
a new command, it may trigger ntmp_clean_cbdr() and free the DMA buffer
while it is still in use. Move ring_lock ownership to the caller to
ensure the response buffer cannot be reclaimed prematurely. So the
helpers ntmp_select_and_lock_cbdr() and ntmp_unlock_cbdr() are added.
These changes eliminate the DMA use-after-free condition and ensure safe
and consistent BD reclamation and DMA buffer lifecycle management.
In the Linux kernel, the following vulnerability has been resolved:
net: airoha: Move ndesc initialization at end of airoha_qdma_init_tx()
If queue entry list allocation fails in airoha_qdma_init_tx_queue routine,
airoha_qdma_cleanup_tx_queue() will trigger a NULL pointer dereference
accessing the queue entry array. The issue is due to the early ndesc
initialization in airoha_qdma_init_tx_queue(). Fix the issue moving ndesc
initialization at end of airoha_qdma_init_tx routine.
In the Linux kernel, the following vulnerability has been resolved:
net: airoha: Move ndesc initialization at end of airoha_qdma_init_rx_queue()
If queue entry or DMA descriptor list allocation fails in
airoha_qdma_init_rx_queue routine, airoha_qdma_cleanup() will trigger a
NULL pointer dereference running netif_napi_del() for RX queue NAPIs
since netif_napi_add() has never been executed to this particular RX NAPI.
The issue is due to the early ndesc initialization in
airoha_qdma_init_rx_queue() since airoha_qdma_cleanup() relies on ndesc
value to check if the queue is properly initialized. Fix the issue moving
ndesc initialization at end of airoha_qdma_init_tx routine.
Move page_pool allocation after descriptor list allocation in order to
avoid memory leaks if desc allocation fails.
In the Linux kernel, the following vulnerability has been resolved:
net: mana: Guard mana_remove against double invocation
If PM resume fails (e.g., mana_attach() returns an error), mana_probe()
calls mana_remove(), which tears down the device and sets
gd->gdma_context = NULL and gd->driver_data = NULL.
However, a failed resume callback does not automatically unbind the
driver. When the device is eventually unbound, mana_remove() is invoked
a second time. Without a NULL check, it dereferences gc->dev with
gc == NULL, causing a kernel panic.
Add an early return if gdma_context or driver_data is NULL so the second
invocation is harmless. Move the dev = gc->dev assignment after the
guard so it cannot dereference NULL.
In the Linux kernel, the following vulnerability has been resolved:
mailbox: mailbox-test: free channels on probe error
On probe error, free the previously obtained channels. This not only
prevents a leak, but also UAF scenarios because the client structure
will be removed nonetheless because it was allocated with devm.
In the Linux kernel, the following vulnerability has been resolved:
mailbox: add sanity check for channel array
Fail gracefully if there is no channel array attached to the mailbox
controller. Otherwise the later dereference will cause an OOPS which
might not be seen because mailbox controllers might instantiate very
early. Remove the comment explaining the obvious while here.
In the Linux kernel, the following vulnerability has been resolved:
mailbox: mailbox-test: don't free the reused channel
The RX channel can be aliased to the TX channel if it has a different
MMIO. This special case needs to be handled when freeing the channels
otherwise a double-free occurs.
In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix AMDGPU_INFO_READ_MMR_REG
There were multiple issues in that code.
First of all the order between the reset semaphore and the mm_lock was
wrong (e.g. copy_to_user) was called while holding the lock.
Then we allocated memory while holding the reset semaphore which is also
a pretty big bug and can deadlock.
Then we used down_read_trylock() instead of waiting for the reset to
finish.
(cherry picked from commit 361b6e6b303d4b691f6c5974d3eaab67ca6dd90e)
In the Linux kernel, the following vulnerability has been resolved:
net: phonet: do not BUG_ON() in pn_socket_autobind() on failed bind
syzbot reported a kernel BUG triggered from pn_socket_sendmsg() via
pn_socket_autobind():
kernel BUG at net/phonet/socket.c:213!
RIP: 0010:pn_socket_autobind net/phonet/socket.c:213 [inline]
RIP: 0010:pn_socket_sendmsg+0x240/0x250 net/phonet/socket.c:421
Call Trace:
sock_sendmsg_nosec+0x112/0x150 net/socket.c:797
__sock_sendmsg net/socket.c:812 [inline]
__sys_sendto+0x402/0x590 net/socket.c:2280
...
pn_socket_autobind() calls pn_socket_bind() with port 0 and, on
-EINVAL, assumes the socket was already bound and asserts that the
port is non-zero:
err = pn_socket_bind(sock, ..., sizeof(struct sockaddr_pn));
if (err != -EINVAL)
return err;
BUG_ON(!pn_port(pn_sk(sock->sk)->sobject));
return 0; /* socket was already bound */
However pn_socket_bind() also returns -EINVAL when sk->sk_state is not
TCP_CLOSE, even when the socket has never been bound and pn_port() is
still 0. In that case the BUG_ON() fires and panics the kernel from a
user-triggerable path.
Treat the "bind returned -EINVAL but pn_port() is still 0" case as a
regular error and propagate -EINVAL to the caller instead of crashing.
Existing callers already translate a non-zero return from
pn_socket_autobind() into -ENOBUFS/-EAGAIN, so returning -EINVAL here
only changes behaviour from panic to a normal errno.
In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda/conexant: Fix missing error check for jack detection
In cx_probe(), the return value of snd_hda_jack_detect_enable_callback()
is ignored. This function returns a pointer, and if it fails (e.g., due
to memory allocation failure), it returns an error pointer which must
be checked using IS_ERR().
If the registration fails, the driver continues to probe, but the jack
detection callback will not be registered. This can lead to a kernel
crash later when the driver attempts to handle jack events or accesses
the uninitialized structure.
Check the return value using IS_ERR() and propagate the error via
PTR_ERR() to the probe caller.
In the Linux kernel, the following vulnerability has been resolved:
drm/xe/eustall: Fix drm_dev_put called before stream disable in close
In xe_eu_stall_stream_close(), drm_dev_put() is called before the
stream is disabled and its resources are freed. If this drops the
last reference, the device structures could be freed while the
subsequent cleanup code still accesses them, leading to a
use-after-free.
Fix this by moving drm_dev_put() after all device accesses are
complete. This matches the ordering in xe_oa_release().
(cherry picked from commit 35aff528f7297e949e5e19c9cd7fd748cf1cf21c)
In the Linux kernel, the following vulnerability has been resolved:
ice: fix NULL pointer dereference in ice_reset_all_vfs()
ice_reset_all_vfs() ignores the return value of ice_vf_rebuild_vsi().
When the VSI rebuild fails (e.g. during NVM firmware update via
nvmupdate64e), ice_vsi_rebuild() tears down the VSI on its error path,
leaving txq_map and rxq_map as NULL. The subsequent unconditional call
to ice_vf_post_vsi_rebuild() leads to a NULL pointer dereference in
ice_ena_vf_q_mappings() when it accesses vsi->txq_map[0].
The single-VF reset path in ice_reset_vf() already handles this
correctly by checking the return value of ice_vf_reconfig_vsi() and
skipping ice_vf_post_vsi_rebuild() on failure.
Apply the same pattern to ice_reset_all_vfs(): check the return value
of ice_vf_rebuild_vsi() and skip ice_vf_post_vsi_rebuild() and
ice_eswitch_attach_vf() on failure. The VF is left safely disabled
(ICE_VF_STATE_INIT not set, VFGEN_RSTAT not set to VFACTIVE) and can
be recovered via a VFLR triggered by a PCI reset of the VF
(sysfs reset or driver rebind).
Note that this patch does not prevent the VF VSI rebuild from failing
during NVM update — the underlying cause is firmware being in a
transitional state while the EMP reset is processed, which can cause
Admin Queue commands (ice_add_vsi, ice_cfg_vsi_lan) to fail. This
patch only prevents the subsequent NULL pointer dereference that
crashes the kernel when the rebuild does fail.
crash> bt
PID: 50795 TASK: ff34c9ee708dc680 CPU: 1 COMMAND: "kworker/u512:5"
#0 [ff72159bcfe5bb50] machine_kexec at ffffffffaa8850ee
#1 [ff72159bcfe5bba8] __crash_kexec at ffffffffaaa15fba
#2 [ff72159bcfe5bc68] crash_kexec at ffffffffaaa16540
#3 [ff72159bcfe5bc70] oops_end at ffffffffaa837eda
#4 [ff72159bcfe5bc90] page_fault_oops at ffffffffaa893997
#5 [ff72159bcfe5bce8] exc_page_fault at ffffffffab528595
#6 [ff72159bcfe5bd10] asm_exc_page_fault at ffffffffab600bb2
[exception RIP: ice_ena_vf_q_mappings+0x79]
RIP: ffffffffc0a85b29 RSP: ff72159bcfe5bdc8 RFLAGS: 00010206
RAX: 00000000000f0000 RBX: ff34c9efc9c00000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000010 RDI: ff34c9efc9c00000
RBP: ff34c9efc27d4828 R8: 0000000000000093 R9: 0000000000000040
R10: ff34c9efc27d4828 R11: 0000000000000040 R12: 0000000000100000
R13: 0000000000000010 R14: R15:
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ff72159bcfe5bdf8] ice_sriov_post_vsi_rebuild at ffffffffc0a85e2e [ice]
#8 [ff72159bcfe5be08] ice_reset_all_vfs at ffffffffc0a920b4 [ice]
#9 [ff72159bcfe5be48] ice_service_task at ffffffffc0a31519 [ice]
#10 [ff72159bcfe5be88] process_one_work at ffffffffaa93dca4
#11 [ff72159bcfe5bec8] worker_thread at ffffffffaa93e9de
#12 [ff72159bcfe5bf18] kthread at ffffffffaa946663
#13 [ff72159bcfe5bf50] ret_from_fork at ffffffffaa8086b9
The panic occurs attempting to dereference the NULL pointer in RDX at
ice_sriov.c:294, which loads vsi->txq_map (offset 0x4b8 in ice_vsi).
The faulting VSI is an allocated slab object but not fully initialized
after a failed ice_vsi_rebuild():
crash> struct ice_vsi 0xff34c9efc27d4828
netdev = 0x0,
rx_rings = 0x0,
tx_rings = 0x0,
q_vectors = 0x0,
txq_map = 0x0,
rxq_map = 0x0,
alloc_txq = 0x10,
num_txq = 0x10,
alloc_rxq = 0x10,
num_rxq = 0x10,
The nvmupdate64e process was performing NVM firmware update:
crash> bt 0xff34c9edd1a30000
PID: 49858 TASK: ff34c9edd1a30000 CPU: 1 COMMAND: "nvmupdate64e"
#0 [ff72159bcd617618] __schedule at ffffffffab5333f8
#4 [ff72159bcd617750] ice_sq_send_cmd at ffffffffc0a35347 [ice]
#5 [ff72159bcd6177a8] ice_sq_send_cmd_retry at ffffffffc0a35b47 [ice]
#6 [ff72159bcd617810] ice_aq_send_cmd at ffffffffc0a38018 [ice]
#7 [ff72159bcd617848] ice_aq_read_nvm at ffffffffc0a40254 [ice]
#8
---truncated---
In the Linux kernel, the following vulnerability has been resolved:
arm64: Reserve an extra page for early kernel mapping
The final part of [data, end) segment may overflow into the next page of
init_pg_end[1] which is the gap page before early_init_stack[2]:
[1]
crash_arm64_v9.0.1> vtop ffffffed00601000
VIRTUAL PHYSICAL
ffffffed00601000 83401000
PAGE DIRECTORY: ffffffecffd62000
PGD: ffffffecffd62da0 => 10000000833fb003
PMD: ffffff80033fb018 => 10000000833fe003
PTE: ffffff80033fe008 => 68000083401f03
PAGE: 83401000
PTE PHYSICAL FLAGS
68000083401f03 83401000 (VALID|SHARED|AF|NG|PXN|UXN)
PAGE PHYSICAL MAPPING INDEX CNT FLAGS
fffffffec00d0040 83401000 0 0 1 4000 reserved
[2]
ffffffed002c8000 (r) __pi__data
ffffffed0054e000 (d) __pi___bss_start
ffffffed005f5000 (b) __pi_init_pg_dir
ffffffed005fe000 (b) __pi_init_pg_end
ffffffed005ff000 (B) early_init_stack
ffffffed00608000 (b) __pi__end
For 4K pages, the early kernel mapping may use 2MB block entries but the
kernel segments are only 64KB aligned. Segment boundaries that fall
within a 2MB block therefore require a PTE table so that different
attributes can be applied on either side of the boundary.
KERNEL_SEGMENT_COUNT still correctly counts the five permanent kernel
VMAs registered by declare_kernel_vmas(). However, since commit
5973a62efa34 ("arm64: map [_text, _stext) virtual address range
non-executable+read-only"), the early mapper also maps [_text, _stext)
separately from [_stext, _etext). This adds one more early-only split
and can require one more page-table page than the existing
EARLY_SEGMENT_EXTRA_PAGES allowance reserves.
Increase the 4K-page early mapping allowance by one page to cover that
additional split.
[catalin.marinas@arm.com: rewrote part of the commit log]
[catalin.marinas@arm.com: expanded the code comment]
In the Linux kernel, the following vulnerability has been resolved:
audit: fix incorrect inheritable capability in CAPSET records
__audit_log_capset() records the effective capability set into the
inheritable field due to a copy-paste error. Every CAPSET audit
record therefore reports cap_pi (process inheritable) with the value
of cap_effective instead of cap_inheritable.
This silently corrupts audit data used for compliance and forensic
analysis: an attacker who modifies inheritable capabilities to
prepare for a privilege-escalating exec would have the change masked
in the audit trail.
The bug has been present since the original introduction of CAPSET
audit records in 2008.
In the Linux kernel, the following vulnerability has been resolved:
idpf: fix double free and use-after-free in aux device error paths
When auxiliary_device_add() fails in idpf_plug_vport_aux_dev() or
idpf_plug_core_aux_dev(), the err_aux_dev_add label calls
auxiliary_device_uninit() and falls through to err_aux_dev_init. The
uninit call will trigger put_device(), which invokes the release
callback (idpf_vport_adev_release / idpf_core_adev_release) that frees
iadev. The fall-through then reads adev->id from the freed iadev for
ida_free() and double-frees iadev with kfree().
Free the IDA slot and clear the back-pointer before uninit, while adev
is still valid, then return immediately.
Commit 65637c3a1811 ("idpf: fix UAF in RDMA core aux dev deinitialization")
fixed the same use-after-free in the matching unplug path in this file but
missed both probe error paths.
In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Wrap DCN32 phantom-plane allocation in DC_RUN_WITH_PREEMPTION_ENABLED
[Why]
dcn32_validate_bandwidth() wraps dcn32_internal_validate_bw() with
DC_FP_START()/DC_FP_END(). In x86 non-RT, DC_FP_START takes fpregs_lock(),
which disables local softirqs.
The DML1 path through dcn32_enable_phantom_plane() calls kvzalloc() to
allocate ~335 KiB for dc_plane_state. This triggers the vmalloc path,
which calls BUG_ON(in_interrupt()) because it's invoked within the
FPU-enabled (softirq disabled) region, leading to a kernel crash.
[How]
Wrap the dc_state_create_phantom_plane() call with the
DC_RUN_WITH_PREEMPTION_ENABLED() macro to allow preemption during
this memory allocation.
(cherry picked from commit 885ccbef7b94a8b38f69c4211c679021aa27ad11)
In the Linux kernel, the following vulnerability has been resolved:
btrfs: only release the dirty pages io tree after successful writes
[WARNING]
With extra warning on dirty extent buffers at umount (aka, the next
patch in the series), test case generic/388 can trigger the following
warning about dirty extent buffers at unmount time:
BTRFS critical (device dm-2 state E): emergency shutdown
BTRFS error (device dm-2 state E): error while writing out transaction: -30
BTRFS warning (device dm-2 state E): Skipping commit of aborted transaction.
BTRFS error (device dm-2 state EA): Transaction 9 aborted (error -30)
BTRFS: error (device dm-2 state EA) in cleanup_transaction:2068: errno=-30 Readonly filesystem
BTRFS info (device dm-2 state EA): forced readonly
BTRFS info (device dm-2 state EA): last unmount of filesystem 4fbf2e15-f941-49a0-bc7c-716315d2777c
------------[ cut here ]------------
WARNING: disk-io.c:3311 at invalidate_and_check_btree_folios+0xfd/0x1ca [btrfs], CPU#8: umount/914368
CPU: 8 UID: 0 PID: 914368 Comm: umount Tainted: G OE 7.1.0-rc1-custom+ #372 PREEMPT(full) 2de38db8d1deae71fde295430a0ff3ab98ccf596
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 02/02/2022
RIP: 0010:invalidate_and_check_btree_folios+0xfd/0x1ca [btrfs]
Call Trace:
<TASK>
close_ctree+0x52e/0x574 [btrfs d2f0b1cd330d1287e7a9919d112eadfc0e914efd]
generic_shutdown_super+0x89/0x1a0
kill_anon_super+0x16/0x40
btrfs_kill_super+0x16/0x20 [btrfs d2f0b1cd330d1287e7a9919d112eadfc0e914efd]
deactivate_locked_super+0x2d/0xb0
cleanup_mnt+0xdc/0x140
task_work_run+0x5a/0xa0
exit_to_user_mode_loop+0x123/0x4b0
do_syscall_64+0x243/0x7c0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
---[ end trace 0000000000000000 ]---
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30539776 owner 9 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30621696 owner 257 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30638080 owner 258 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30654464 owner 7 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30703616 owner 2 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30720000 owner 10 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30736384 owner 4 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30752768 owner 11 gen 9 refs 2 flags 0x7
I'm using a stripped down version, which seems to trigger the warning
more reliably:
_fsstress_pid=""
workload()
{
dmesg -C
mkfs.btrfs -f -K $dev > /dev/null
echo 1 > /sys/kernel/debug/clear_warn_once
mount $dev $mnt
$fsstress -w -n 1024 -p 4 -d $mnt &
_fsstress_pid=$!
sleep 0
$godown $mnt
pkill --echo -PIPE fsstress > /dev/null
wait $_fsstress_pid
unset _fsstress_pid
umount $mnt
if dmesg | grep -q "WARNING"; then
fail
fi
}
for (( i = 0; i < $runtime; i++ )); do
echo "=== $i/$runtime ==="
workload
done
[CAUSE]
Inside btrfs_write_and_wait_transaction(), we first try to write all
dirty ebs, then wait for them to finish.
After that we call btrfs_extent_io_tree_release() to free all
extent states from dirty_pages io tree.
However if we hit an error from btrfs_write_marked_extent(), then we
still call btrfs_extent_io_tree_release() to clear that dirty_pages io
tree, which may contain dirty records that we haven't yet submitted.
Furthermore, the later transaction cleanup path will utilize that
dirty_pages io tree to properly cleanup those dirty ebs, but since it's
already empty, no dirty ebs are properly cleaned up, thus will later
trigger the warnings inside invalidate_btree_folios().
---truncated---
In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Bounds-check devid in __rlookup_amd_iommu()
iommu_device_register() walks every device on the PCI bus via
bus_for_each_dev() and calls amd_iommu_probe_device() for each. The
inlined check_device() path computes the device's sbdf, calls
rlookup_amd_iommu() to find the owning IOMMU, and only afterwards
verifies devid <= pci_seg->last_bdf. __rlookup_amd_iommu() indexes
rlookup_table[devid] with no bounds check of its own, so for a PCI
device whose BDF is not described by the IVRS, the lookup reads past
the end of the allocation before the caller's bounds check can run.
This was harmless before commit e874c666b15b ("iommu/amd: Change
rlookup, irq_lookup, and alias to use kvalloc()"): the table was a
zeroed page-order allocation, so the over-read returned NULL and the
caller's NULL check skipped the device. After that commit the table is
a tight kvcalloc() and the over-read returns adjacent slab contents,
which check_device() then dereferences as a struct amd_iommu *,
causing a boot-time GPF.
Seen on Google Compute Engine ct6e VMs, where the virtualized IVRS
describes only the four TPU endpoints 00:04.0-07.0; the gVNIC at
00:08.0 (devid 0x40) indexes 56 bytes past the 456-byte allocation,
into the adjacent kmalloc-512 slab object:
pci 0000:00:04.0: Adding to iommu group 0
pci 0000:00:05.0: Adding to iommu group 1
pci 0000:00:06.0: Adding to iommu group 2
pci 0000:00:07.0: Adding to iommu group 3
Oops: general protection fault, probably for non-canonical address 0x3a64695f78746382: 0000 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.18.22 #1
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 12/06/2025
RIP: 0010:amd_iommu_probe_device+0x54/0x3a0
Call Trace:
__iommu_probe_device+0x107/0x520
probe_iommu_group+0x29/0x50
bus_for_each_dev+0x7e/0xe0
iommu_device_register+0xc9/0x240
iommu_go_to_state+0x9c0/0x1c60
amd_iommu_init+0x14/0x40
pci_iommu_init+0x16/0x60
do_one_initcall+0x47/0x2f0
Guard the array access in __rlookup_amd_iommu(). With the fix applied
on 6.18.22, the gVNIC at 00:08.0 is skipped cleanly and the VM boots.
In the Linux kernel, the following vulnerability has been resolved:
x86/kexec: Push kjump return address even for non-kjump kexec
The version of purgatory code shipped by kexec-tools attempts to look above
the top of its stack to find a return address for a kjump, even in a non-kjump
kexec.
After the commit in Fixes: the word above the stack might not be there,
leading to a fault (which is at least now caught by my exception-handling code
in kexec).
That commit fixed things for the actual kjump path, but no longer
"gratuitously" pushes the unused return address to the stack in the non-kjump
path. Put that *back* in the non-kjump path, to prevent purgatory from
crashing when trying to access it.
In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Avoid NULL pointer dereference or refcount corruption
Commit 60f030f7418d ("iommu/vt-d: Avoid use of NULL after WARN_ON_ONCE")
fixed a NULL pointer dereference in an unlikely situation partly.
If dev_pasid is not found in the dev_pasids list, it remains NULL.
However, the teardown operations are executed unconditionally, this lead
to a NULL pointer dereference or refcount corruption.
If the domain was never attached to this IOMMU, info will be NULL, which
would cause an immediate dereference when checking --info->refcnt.
Even if info is not NULL, decrementing the refcount without having removed
a valid PASID might unbalance the count. This could lead to premature
dropping of the refcount to 0, potentially causing a use-after-free for the
remaining active devices sharing the domain.
Fix it by returning early if dev_pasid is NULL, before executing the
teardown operations.
Issue found by AI review and suggested by Kevin Tian.
https://sashiko.dev/#/patchset/20260421031347.1408890-1-zhenzhong.duan%40intel.com
In the Linux kernel, the following vulnerability has been resolved:
iommu: Fix NULL group->domain dereference in pci_dev_reset_iommu_done()
Local sashiko review pointed it out that group->domain could be NULL when
a default domain fails to allocate during the first probe, which can crash
at domain->ops->attach_dev dereference in __iommu_attach_device() invoked
by pci_dev_reset_iommu_done().
pci_dev_reset_iommu_prepare() is fine as an old_domain pointer can be NULL.
Skip the re-attach in pci_dev_reset_iommu_done() to fix the bug.
In the Linux kernel, the following vulnerability has been resolved:
drm/gma500/oaktrail_lvds: fix hang on init failure
The LVDS init code looks up an I2C adapter using i2c_get_adapter() and
tries to read the EDID before falling back to allocating and registering
its own adapter.
The error handling does not separate these cases so on a late init
failure it will try to deregister and free also an adapter that had
previously been registered. Since i2c_get_adapter() takes another
reference to the adapter, deregistration hangs indefinitely while
waiting for the reference to be released.
Fix this by only destroying adapters allocated during LVDS init on
errors.
In the Linux kernel, the following vulnerability has been resolved:
arm_mpam: Check whether the config array is allocated before destroying it
__destroy_component_cfg() is called to free the configuration array.
It uses the embedded 'garbage' structure, which means the array has
to be allocated.
If __destroy_component_cfg() is called from mpam_disable() before the
configuration was ever allocated, then a NULL pointer is dereferenced.
Check for this case and return early if the configuration is not
allocated.
__destroy_component_cfg() also frees the mbwu_state as this is allocated
by __allocate_component_cfg(). As the mbwu_state is allocated after
comp->cfg is set, and is also under mpam_list_lock, only the first
pointer needs checking.
OpenProject is open-source, web-based project management software. Prior to 17.3.3 and 17.4.1, there is a SQL injection in timestamps functionality. OpenProject baseline comparison allows callers to request historic work-package attributes using the timestamps parameter. This vulnerability is fixed in 17.3.3 and 17.4.1.
OpenProject is open-source, web-based project management software. Prior to 17.3.3 and 17.4.1, there is a CSRF on TARGET through /users/:id via POST parameter "user[admin]". This vulnerability is fixed in 17.3.3 and 17.4.1.
OpenProject is open-source, web-based project management software. Prior to 17.3.3 and 17.4.1, OpenProject's Storages module writes the OneDrive/SharePoint userless OAuth access_token plaintext to Rails.cache under the deterministic key storage.<id>.httpx_access_token, repopulated continuously by an hourly cron and every userless-OAuth call site (see Write cadence). None of the three allowed cache backends (file_store, memcache, redis) encrypts at rest. An attacker with read access to the cache backend recovers the Azure-AD application-tier bearer with an anonymous get over the memcached binary protocol (or the equivalent against Redis). This vulnerability is fixed in 17.3.3 and 17.4.1.
OpenProject is open-source, web-based project management software. Prior to 17.3.3 and 17.4.1, there is an IDOR through /projects/<A>/settings/project_storages/<A_ps_id> via PATCH parameter "storages_project_storage[project_folder_id]" leads to Access to Unauthorized Resources. A project-admin in one project can hijack the managed Nextcloud or OneDrive folder of another project on the same storage by writing the victim project's project_folder_id into the attacker's Storages::ProjectStorage row. The next managed-folder sync overwrites the ACL on the referenced folder with the attacker project's user list. This vulnerability is fixed in 17.3.3 and 17.4.1.
OpenProject is open-source, web-based project management software. Prior to 17.3.3 and 17.4.1, the HTML sanitizer grants <macro> elements unrestricted data-* attributes via :data wildcard. An attacker injects data-controller="poll-for-changes" into a work package description, causing Stimulus.js to mount a controller that fetches an attacker-uploaded attachment and passes it to renderStreamMessage(). This executes arbitrary Turbo Stream actions — including redirect_to — in every victim's authenticated browser session, redirecting them to an attacker-controlled server. This vulnerability is fixed in 17.3.3 and 17.4.1.
OpenProject is open-source, web-based project management software. Prior to 17.3.3 and 17.4.1, cache store poisoning leads to Remote Code Execution (RCE). This vulnerability is fixed in 17.3.3 and 17.4.1.
OpenProject is open-source, web-based project management software. Prior to 17.3.3 and 17.4.1, a cross-project IDOR / authorization context confusion in the Calendar and Team Planner modules allows a user with management permissions in one project to delete public Calendar or Team Planner Queries from another project where they do not have the corresponding management permissions. Both modules authorize the request against the project identified by :project_id in the URL, but the actual Query object is loaded later by :id from Query.visible(current_user) without verifying that the loaded Query belongs to the authorized project. As a result, an attacker can use permissions from Project A to delete shared/public Calendar or Team Planner views from Project B, causing integrity impact and limited availability impact for users relying on those shared views. This vulnerability is fixed in 17.3.3 and 17.4.1.
RustFS is a distributed object storage system built in Rust. In 1.0.0-beta.4, authenticated users with only PutObject permission on their own bucket can exploit a path traversal vulnerability in the Snowball auto-extract feature to write arbitrary objects into other users' buckets, completely breaking multi-tenant isolation. The vulnerability chains three flaws: No ../ sanitization in tar entry key normalization; IAM wildcard matching uses raw (uncleaned) paths; and Filesystem path cleaning resolves ../ across bucket boundaries.
OpenProject is open-source, web-based project management software. Prior to 17.4.0, `GET /api/v3/meetings/:meeting_id/agenda_items/:agenda_item_id` discloses private work package data from a linked work package that belongs to a private/inaccessible project. This vulnerability is fixed in 17.4.0.
OpenProject is open-source, web-based project management software. Prior to 17.3.3 and 17.4.1, the journal diff endpoint discloses hidden historical field values without enforcing object and field visibility. This vulnerability is fixed in 17.3.3 and 17.4.1.
OpenProject is open-source, web-based project management software. Prior to , the official openproject/openproject Docker image ships ENV SECRET_KEY_BASE=OVERWRITE_ME as the default Rails master key. Combined with cookies_serializer = :marshal, this gives any logged-in user a deterministic Marshal-deserialization path reachable via the /my/two_factor_devices cookie reader This vulnerability is fixed in .
OpenProject is open-source, web-based project management software. Prior to 17.4.0, the GET /api/v3/relations endpoint allows any authenticated user to retrieve relations — and the subject (title) of work packages they have no permission to view — by supplying an arbitrary work package ID in the involved, fromId, or toId filter. This bypasses the Relation.visible scope due to a flawed performance optimization in RelationQuery. This vulnerability is fixed in 17.4.0.
OpenProject is open-source, web-based project management software. Prior to 17.3.2 and 17.4.0, the GET /api/v3/shares endpoint returns share details for ALL work packages in a project to any user with the view_shared_work_packages permission. The authorization check operates at the project level only — it does not verify the requesting user can actually view each individual shared work package. This allows a regular project member to discover work package IDs and subjects (including confidential titles), which users have been granted shared access, what role level was assigned (Editor, Commenter, Viewer). This vulnerability is fixed in 17.3.2 and 17.4.0.
OpenProject is open-source, web-based project management software. Prior to 17.3.2 and 17.4.0, a Missing Authorization vulnerability exists in OpenProject's CostReportsController. The rename and update actions allow any authenticated user to modify the name, filters, and grouping of any Public cost report in the system without verifying ownership or permission level. An attacker who discovers or guesses a public report's numeric ID can rename or overwrite its filter configuration without any warning to the report's owner. This vulnerability is fixed in 17.3.2 and 17.4.0.
OpenProject is open-source, web-based project management software. Prior to 17.3.2 and 17.4.0, Business Logic Error on OpenProject through PATCH request to /api/v3/users/me permits to bypass password requirements. A password validation flaw in the change password behavior allows attackers to change a user's password only with an active session takeover. This vulnerability is fixed in 17.3.2 and 17.4.0.
OpenProject is open-source, web-based project management software. Prior to 17.3.2 and 17.4.0, OpenProject exposes a document update endpoint used to modify existing documents. The target document is loaded with visibility checks and then updated. During update, attacker-controlled attributes are applied to the persisted record before authorization is enforced. As a result, a user without :manage_documents in the source project can move and modify foreign project documents by setting project_id in a single PATCH request. This vulnerability is fixed in 17.3.2 and 17.4.0.
OpenProject is open-source, web-based project management software. Prior to 17.3.2 and 17.4.0, the web application's meetings filter feature leaks whether a given user ID corresponds to a valid account and discloses the user's full name, allowing an attacker to enumerate all existing user accounts by probing user IDs and observing differences in the server response. This vulnerability is fixed in 17.3.2 and 17.4.0.