直近表示から外れた情報を確認できます。診断結果とは別情報として扱います。
In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: enforce HE/EHT cap/oper consistency Xiang Mei reports that mac80211 could crash if eht_cap is set but eht_oper isn't. Rather than fixing that for the individual user(s), enforce that both HE/EHT have consistent elements.
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: RFCOMM: hold listener socket in rfcomm_connect_ind() rfcomm_get_sock_by_channel() scans rfcomm_sk_list under the list lock, but returns the selected listener after dropping that lock without taking a reference. rfcomm_connect_ind() then locks the listener, queues a child socket on it, and may notify it after unlocking it. The buggy scenario involves two paths, with each column showing the order within that path: rfcomm_connect_ind(): listener close: 1. Find parent in 1. close() enters rfcomm_get_sock_by_channel() rfcomm_sock_release(). 2. Drop rfcomm_sk_list.lock 2. rfcomm_sock_shutdown() without pinning parent. closes the listener. 3. Call lock_sock(parent) and 3. rfcomm_sock_kill() bt_accept_enqueue(parent, unlinks and puts parent. sk, true). 4. Read parent flags and may 4. parent can be freed. call sk_state_change(). If close wins the race, parent can be freed before rfcomm_connect_ind() reaches lock_sock(), bt_accept_enqueue(), or the deferred-setup callback. Take a reference on the listener before leaving rfcomm_sk_list.lock. After lock_sock() succeeds, recheck that it is still in BT_LISTEN before queueing a child, cache the deferred-setup bit while the parent is locked, and drop the reference after the last parent use. KASAN reported a slab-use-after-free in lock_sock_nested() from rfcomm_connect_ind(), with the freeing stack going through rfcomm_sock_kill() and rfcomm_sock_release().
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: MGMT: validate advertising TLV before type checks tlv_data_is_valid() reads each advertising data field length from data[i], then inspects data[i + 1] for managed EIR types before checking that the current field still fits inside the supplied buffer. A malformed field whose length byte is the last byte of the buffer can therefore make the parser read one byte past the advertising data. KASAN reported the following when a malformed MGMT_OP_ADD_ADVERTISING request reached that path: BUG: KASAN: vmalloc-out-of-bounds in tlv_data_is_valid() Read of size 1 Call trace: tlv_data_is_valid() add_advertising() hci_mgmt_cmd() hci_sock_sendmsg() Move the existing element-length check before any type-octet inspection so each non-empty element is proven to contain its type byte before the parser looks at data[i + 1].
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: RFCOMM: validate skb length in MCC handlers The RFCOMM MCC handlers cast skb->data to protocol-specific structs without validating skb->len first. A malicious remote device can send truncated MCC frames and trigger out-of-bounds reads in these handlers. Fix this by using skb_pull_data() to validate and access the required data before dereferencing it. rfcomm_recv_rpn() requires special handling since ETSI TS 07.10 allows 1-byte RPN requests. Handle this by validating only the DLCI byte first, and validating the full struct only when len > 1.
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: bnep: reject short frames before parsing A BNEP peer can send a short BNEP SDU. bnep_rx_frame() reads the packet type byte immediately and, for control packets, reads the control opcode and setup UUID-size byte before proving that those bytes are present. bnep_rx_control() also dereferences the control opcode without rejecting an empty control payload. Use skb_pull_data() for the fixed fields in bnep_rx_frame() so a NULL return gates each dereference. Split the control handler so the frame path can pass an opcode that has already been pulled, and keep the byte-buffer wrapper for extension control payloads. For BNEP_SETUP_CONN_REQ, name the UUID-size byte before pulling the setup payload. struct bnep_setup_conn_req carries destination and source service UUIDs after that byte, each uuid_size bytes, so the parser now documents that tuple explicitly instead of leaving the pull length as an opaque multiplication. Validation reproduced this kernel report: KASAN slab-out-of-bounds in bnep_rx_frame.isra.0+0x130c/0x1790 The buggy address belongs to the object at ffff88800c0f7908 which belongs to the cache kmalloc-8 of size 8 The buggy address is located 0 bytes to the right of allocated 1-byte region [ffff88800c0f7908, ffff88800c0f7909) Read of size 1 Call trace: dump_stack_lvl+0xb3/0x140 (?:?) print_address_description+0x57/0x3a0 (?:?) bnep_rx_frame+0x130c/0x1790 (net/bluetooth/bnep/core.c:306) print_report+0xb9/0x2b0 (?:?) __virt_addr_valid+0x1ba/0x3a0 (?:?) srso_alias_return_thunk+0x5/0xfbef5 (?:?) kasan_addr_to_slab+0x21/0x60 (?:?) kasan_report+0xe0/0x110 (?:?) process_one_work+0xfce/0x17e0 (kernel/workqueue.c:3200) worker_thread+0x65c/0xe40 (?:?) __kthread_parkme+0x184/0x230 (?:?) kthread+0x35e/0x470 (?:?) _raw_spin_unlock_irq+0x28/0x50 (?:?) ret_from_fork+0x586/0x870 (?:?) __switch_to+0x74f/0xdc0 (?:?) ret_from_fork_asm+0x1a/0x30 (?:?)
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: fix memory leak in error path of hci_alloc_dev() Early failures in Bluetooth HCI UART configuration leak SRCU percpu memory. When device initialization fails before hci_register_dev() completes, the HCI_UNREGISTER flag is never set. As a result, when the device reference count reaches zero, bt_host_release() evaluates this flag as false and falls back to a direct kfree(hdev). Because hci_release_dev() is bypassed, the SRCU struct initialized early in hci_alloc_dev() is never cleaned up, resulting in a leak of percpu memory. Fix the leak by explicitly calling cleanup_srcu_struct() in the fallback (unregistered) branch of bt_host_release() before freeing the device.
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: ISO: Fix not releasing hdev reference on iso_conn_big_sync hci_get_route() returns a reference-counted hci_dev pointer via hci_dev_hold(). The function exits normally or with an error without ever releasing it.
In the Linux kernel, the following vulnerability has been resolved: xsk: cache csum_start/csum_offset to fix TOCTOU in xsk_skb_metadata() The TX metadata area resides in the UMEM buffer which is memory-mapped and concurrently writable by userspace. In xsk_skb_metadata(), csum_start and csum_offset are read from shared memory for bounds validation, then read again for skb assignment. A malicious userspace application can race to overwrite these values between the two reads, bypassing the bounds check and causing out-of-bounds memory access during checksum computation in the transmit path. Fix this by reading csum_start and csum_offset into local variables once, then using the local copies for both validation and assignment. Note that other metadata fields (flags, launch_time) and the cached csum fields may be mutually inconsistent due to concurrent userspace writes, but this is benign: the only security-critical invariant is that each field's validated value is the same one used, which local caching guarantees.
In the Linux kernel, the following vulnerability has been resolved: ipv4: restrict IPOPT_SSRR and IPOPT_LSRR options This patch restricts setting Loose Source and Record Route (LSRR) and Strict Source and Record Route (SSRR) IP options to users with CAP_NET_RAW capability. This prevents unprivileged applications from forcing packets to route through attacker-controlled nodes to leak TCP ISN and possibly other protocol information. While LSRR and SSRR are commonly filtered in many network environments, they may still be supported and forwarded along some network paths. RFC 7126 (Recommendations on Filtering of IPv4 Packets Containing IPv4 Options) recommend to drop these options in 4.3 and 4.4.
In the Linux kernel, the following vulnerability has been resolved: net: airoha: Fix use-after-free in metadata dst teardown airoha_metadata_dst_free() runs metadata_dst_free() which frees the metadata_dst with kfree() immediately, bypassing the RCU grace period. In the RX path, skb_dst_set_noref() sets a non-refcounted pointer from the skb to the metadata_dst. This function requires RCU read-side protection and the dst must remain valid until all RCU readers complete. Since metadata_dst_free() calls kfree() directly, an use-after-free can occur if any skb still holds a noref pointer to the dst when the driver tears it down. Replace metadata_dst_free() with dst_release() which properly goes through the refcount path: when the refcount drops to zero, it schedules the actual free via call_rcu_hurry(), ensuring all RCU readers have completed before the memory is freed.
In the Linux kernel, the following vulnerability has been resolved: net: ethernet: mtk_eth_soc: Fix use-after-free in metadata dst teardown mtk_free_dev() calls metadata_dst_free() which frees the metadata_dst with kfree() immediately, bypassing the RCU grace period. In the RX path, skb_dst_set_noref() sets a non-refcounted pointer from the skb to the metadata_dst. This function requires RCU read-side protection and the dst must remain valid until all RCU readers complete. Since metadata_dst_free() calls kfree() directly, a use-after-free can occur if any skb still holds a noref pointer to the dst when the driver tears it down. Replace metadata_dst_free() with dst_release() which properly goes through the refcount path: when the refcount drops to zero, it schedules the actual free via call_rcu_hurry(), ensuring all RCU readers have completed before the memory is freed.
In the Linux kernel, the following vulnerability has been resolved: sctp: validate cached peer INIT chunk length in COOKIE_ECHO processing When a listening SCTP server processes a COOKIE_ECHO chunk, the cached peer INIT chunk embedded after the cookie is parsed and its parameters are later walked by sctp_process_init() using sctp_walk_params(). However, the chunk header length of this cached INIT chunk was not validated against the remaining buffer in the COOKIE_ECHO payload. If the length field is inflated, the parameter walk can run beyond the actual received data, leading to out-of-bounds reads and potential memory corruption during later parameter handling (e.g. STATE_COOKIE processing and kmemdup() copies). Add a bounds check in sctp_unpack_cookie() to ensure the cached INIT chunk length does not exceed the available data in the COOKIE_ECHO buffer before it is used.
In the Linux kernel, the following vulnerability has been resolved: net/802/mrp: fix vector attribute parsing in mrp_pdu_parse_vecattr In mrp_pdu_parse_vecattr(), vector attribute events are encoded three per byte and valen tracks the number of events left to process. The parser decrements valen after processing the first and second events from each event byte, but not after processing the third one. When valen is exactly a multiple of three, the loop continues after the last valid event and consumes the next byte as a new event byte, applying a spurious event to the MRP applicant state. Additionally, when valen is zero the parser unconditionally consumes attrlen bytes as FirstValue and advances the offset, even though per IEEE 802.1ak a VectorAttribute with only a LeaveAllEvent has valen of zero and no FirstValue or Vector fields. This corrupts the offset for subsequent PDU parsing. Also, when valen exceeds three the loop crosses byte boundaries but the attribute value is not incremented between the last event of one byte and the first event of the next. This causes the first event of the next byte to use the same attribute value as the third event rather than the next consecutive value. Decrement valen after processing the third event, skip FirstValue consumption when valen is zero, and increment the attribute value at the end of each loop iteration.
In the Linux kernel, the following vulnerability has been resolved: VFS: fix possible failure to unlock in nfsd4_create_file() atomic_create() in fs/namei.c drops the reference to the dentry when it returns an error. This behaviour was imported into dentry_create() so that it will drop the reference if an error is returned from atomic_create(), though not if vfs_create() returns an error (in the case where ->atomic_create is not supported). The caller - nfsd4_create_file() - is made aware of this by checking path->dentry, which will either be a counted reference to a dentry, or an error pointer. However the change to use start_creating()/end_creating() (which landed shortly before the dentry_create() change landed, though was likely developed around the same time) means that nfsd4_create_file() *needs* a valid dentry so that it can unlock the parent. The net result is that if NFSD exports a filesystem which uses ->atomic_create, and if a call to ->atomic_create returns an error, then nfsd4_create_file() will pass an error pointer to end_creating() and the parent will not be unlocked. Fix this by changing dentry_create() to make sure path->dentry is always a valid dentry, never an error-pointer. The actual error is already returned a different way. Note that if ->atomic_create() returns a different dentry (which may not be possible in practice) we are guaranteed (because it is only ever provided by d_spliace_alias()) that it will have the same d_parent and so it will have the same effect when passed to end_creating().
In the Linux kernel, the following vulnerability has been resolved: rseq: Fix using an uninitialized stack variable in rseq_exit_user_update() There is an bug in which an uninitialized stack variable is used in rseq_exit_user_update() as reported by syzbot: BUG: KMSAN: kernel-infoleak in rseq_set_ids_get_csaddr include/linux/rseq_entry.h:502 [inline] The local variable: struct rseq_ids ids = { .cpu_id = task_cpu(t), .mm_cid = task_mm_cid(t), .node_id = cpu_to_node(ids.cpu_id), }; According to the C standard, the evaluation order of expressions in an initializer list is indeterminately sequenced. The compiler (Clang, in this KMSAN build) evaluates `cpu_to_node(ids.cpu_id)` *before* `ids.cpu_id` is initialized with `task_cpu(t)`. This is fixed by moving the assignment of ids.node_id outside the structure initialization.
In the Linux kernel, the following vulnerability has been resolved: ALSA: PCM: Fix wait queue list corruption in snd_pcm_drain() on linked streams snd_pcm_drain() uses init_waitqueue_entry which does not clear entry.prev/next, and add_wait_queue with a conditional remove_wait_queue that is skipped when to_check is no longer in the group after concurrent UNLINK. The orphaned wait entry remains on the unlinked substream sleep queue. On the next drain iteration, add_wait_queue adds the entry to a new queue while still linked on the old one, corrupting both lists. A subsequent wake_up dereferences NULL at the func pointer (mapped from the spinlock at offset 0 of the misinterpreted wait_queue_head_t), causing a kernel panic. Replace init_waitqueue_entry/add_wait_queue/conditional remove_wait_queue with init_wait_entry/prepare_to_wait/ finish_wait. init_wait_entry clears prev/next via INIT_LIST_HEAD on each iteration and sets autoremove_wake_function which auto-removes the entry on wake-up. finish_wait safely handles both the already-removed and still-queued cases.
In the Linux kernel, the following vulnerability has been resolved: ALSA: seq: dummy: fix UMP event stack overread The dummy sequencer port forwards events by copying an incoming struct snd_seq_event into a stack temporary, rewriting source and destination, and dispatching the temporary to subscribers. That legacy event storage is smaller than struct snd_seq_ump_event. When a UMP event reaches the dummy client, the copy leaves the UMP flag set but only provides legacy-sized stack storage. The subscriber delivery path then uses snd_seq_event_packet_size() and copies a UMP-sized packet from that stack object, reading past the end of the temporary. Use the existing union __snd_seq_event storage and copy the packet size reported for the incoming event before rewriting the common routing fields. This preserves the full UMP packet for UMP events while keeping legacy event handling unchanged.
In the Linux kernel, the following vulnerability has been resolved: xfrm: iptfs: fix use-after-free on first_skb in __input_process_payload __input_process_payload() stores first_skb into xtfs->ra_newskb under drop_lock when starting partial reassembly, then unlocks and breaks out of the processing loop. The post-loop check reads xtfs->ra_newskb without the lock to decide whether first_skb is still owned: if (first_skb && first_iplen && !defer && first_skb != xtfs->ra_newskb) Between spin_unlock and this read, a concurrent CPU running iptfs_reassem_cont() (or the drop_timer hrtimer) can complete reassembly, NULL xtfs->ra_newskb, and free the skb. The check then evaluates first_skb != NULL as true, and pskb_trim/ip_summed/consume_skb operate on the freed skb — a use-after-free in skbuff_head_cache. Replace the unlocked read with a local bool that records whether first_skb was handed to the reassembly state in the current call. The flag is set after the existing spin_unlock, before the break, using the pointer equality that is stable at that point (first_skb == skb iff first_skb was stored in ra_newskb).
In the Linux kernel, the following vulnerability has been resolved: xfrm: policy: fix use-after-free on inexact bin in xfrm_policy_bysel_ctx() Fix the race by pruning the bin while still holding xfrm_policy_lock, before dropping it. Use __xfrm_policy_inexact_prune_bin() directly since the lock is already held. The wrapper xfrm_policy_inexact_prune_bin() becomes unused and is removed. Race: CPU0 (XFRM_MSG_DELPOLICY) CPU1 (XFRM_MSG_NEWSPDINFO) ========================== ========================== xfrm_policy_bysel_ctx(): spin_lock_bh(xfrm_policy_lock) bin = xfrm_policy_inexact_lookup() __xfrm_policy_unlink(pol) spin_unlock_bh(xfrm_policy_lock) xfrm_policy_kill(ret) // wide window, lock not held xfrm_hash_rebuild(): spin_lock_bh(xfrm_policy_lock) __xfrm_policy_inexact_flush(): kfree_rcu(bin) // bin freed spin_unlock_bh(xfrm_policy_lock) xfrm_policy_inexact_prune_bin(bin) // UAF: bin is freed
In the Linux kernel, the following vulnerability has been resolved: netlabel: validate unlabeled address and mask attribute lengths netlbl_unlabel_addrinfo_get() used the address attribute length to determine whether the attribute data could be read as an IPv4 or IPv6 address, but did not independently validate the corresponding mask attribute length. A crafted Generic Netlink request could therefore provide a valid IPv4/IPv6 address attribute with a shorter mask attribute, which would later be read as a full struct in_addr or struct in6_addr. NLA_BINARY policy lengths are maximum lengths by default, so use NLA_POLICY_EXACT_LEN() for the unlabeled IPv4/IPv6 address and mask attributes. This rejects short attributes during policy validation and also exposes the exact length requirements through policy introspection.
In the Linux kernel, the following vulnerability has been resolved: gpio: mvebu: fix NULL pointer dereference in suspend/resume mvebu_pwm_suspend() and mvebu_pwm_resume() are called for all GPIO banks during suspend/resume, but not all banks have PWM functionality. GPIO banks without PWM have mvchip->mvpwm set to NULL. Calling mvebu_pwm_suspend() with mvpwm == NULL causes a NULL pointer dereference when it tries to access mvpwm->blink_select. Unable to handle kernel NULL pointer dereference at virtual address 00000020 when write [00000020] *pgd=00000000 Internal error: Oops: 815 [#1] PREEMPT ARM Modules linked in: CPU: 0 UID: 0 PID: 406 Comm: sh Not tainted 6.12.74-rt12-yocto-standard-g4e96f98fb7db-dirty #353 Hardware name: Marvell Armada 370/XP (Device Tree) PC is at regmap_mmio_read+0x38/0x54 LR is at regmap_mmio_read+0x38/0x54 pc : [<c05fd2ac>] lr : [<c05fd2ac>] psr: 200f0013 sp : f0c11d10 ip : 00000000 fp : c100d2f0 r10: c14fb854 r9 : 00000000 r8 : 00000000 r7 : c1799c00 r6 : 00000020 r5 : 00000020 r4 : c179c7c0 r3 : f0a231a0 r2 : 00000020 r1 : 00000020 r0 : 00000000 Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 135ec059 DAC: 00000051 Call trace: regmap_mmio_read from _regmap_bus_reg_read+0x78/0xac _regmap_bus_reg_read from _regmap_read+0x60/0x154 _regmap_read from regmap_read+0x3c/0x60 regmap_read from mvebu_gpio_suspend+0xa4/0x14c mvebu_gpio_suspend from dpm_run_callback+0x54/0x180 dpm_run_callback from device_suspend+0x124/0x630 device_suspend from dpm_suspend+0x124/0x270 dpm_suspend from dpm_suspend_start+0x64/0x6c dpm_suspend_start from suspend_devices_and_enter+0x140/0x8e8 suspend_devices_and_enter from pm_suspend+0x2fc/0x308 pm_suspend from state_store+0x6c/0xc8 state_store from kernfs_fop_write_iter+0x10c/0x1f8 kernfs_fop_write_iter from vfs_write+0x270/0x468 vfs_write from ksys_write+0x70/0xf0 ksys_write from ret_fast_syscall+0x0/0x54 Add a NULL check for mvchip->mvpwm before calling the PWM suspend/resume functions.
In the Linux kernel, the following vulnerability has been resolved: tcp: restrict SO_ATTACH_FILTER to priv users This patch restricts the use of SO_ATTACH_FILTER (cBPF) on TCP sockets to users with CAP_NET_ADMIN capability. This blocks potential side-channel attack where an unprivileged application attaches a filter to leak TCP sequence/acknowledgment numbers.
In the Linux kernel, the following vulnerability has been resolved: net: add pskb_may_pull() to skb_gro_receive_list() skb_gro_receive_list() calls skb_pull(skb, skb_gro_offset(skb)) without first ensuring the data is in the linear area via pskb_may_pull(). When the skb arrives via napi_gro_frags(), skb_headlen can be 0 (all data in page fragments) while skb_gro_offset is non-zero (after IP+TCP header parsing). The skb_pull() then decrements skb->len by skb_gro_offset but skb->data_len stays unchanged, hitting BUG_ON(skb->len < skb->data_len) in __skb_pull(). The UDP fraglist GRO path already contains this guard at udp_offload.c:749. Adding it to skb_gro_receive_list() itself provides centralized protection for all callers (TCP, UDP, and any future protocols), and ensures the precondition of skb_pull() is satisfied before it is called. On pskb_may_pull() failure, set NAPI_GRO_CB(skb)->flush = 1 so the skb is not held as a new GRO head and is instead delivered through the normal receive path, matching the UDP handling.
In the Linux kernel, the following vulnerability has been resolved: net: ibm: emac: Fix use-after-free during device removal The driver was using devm_register_netdev() which causes unregister_netdev() to be deferred until the devres cleanup phase, which runs after emac_remove() returns. This creates a use-after-free window where: 1. emac_remove() is called, which tears down hardware (cancels work, detaches modules, unregisters from MAL) 2. emac_remove() returns 3. devres cleanup runs and finally calls unregister_netdev() During step 3, the network stack might still process packets, triggering emac_irq(), emac_poll(), or other handlers that access now-freed hardware resources (dev->emacp, dev->mal, etc.). Fix this by replacing devm_register_netdev() with manual register_netdev() and calling unregister_netdev() at the beginning of emac_remove(), before any hardware teardown. This ensures the network device is fully stopped and unregistered before hardware resources are released. The change is safe because: - dev->ndev is assigned very early in probe (before any error paths that could bypass emac_remove) - platform_set_drvdata() is only called after successful registration, so emac_remove() only runs for fully registered devices - unregister_netdev() is idempotent and safe to call on any registered device
In the Linux kernel, the following vulnerability has been resolved: netdev: fix double-free in netdev_nl_bind_rx_doit() Sashiko flags that genlmsg_reply() always consumes the skb. The error path calls nlmsg_free(rsp) so we can't jump directly to it. Let's not unbind, just propagate the error to the user. This is the typical way of handling genlmsg_reply() failures. They shouldn't happen unless user does something silly like calling the kernel with an already-full rcvbuf.
In the Linux kernel, the following vulnerability has been resolved: net: phy: clean the sfp upstream if phy probing fails Sashiko reported that we don't call sfp_bus_del_upstream() in the probe failure path, so let's add it, otherwise the sfp-bus is left with a dangling 'upstream' field, that may be used later on during SFP events. This issue existed before the generic phylib sfp support, back when drivers were calling phy_sfp_probe themselves.
In the Linux kernel, the following vulnerability has been resolved: net: phy: don't try to setup PHY-driven SFP cages when using genphy We don't have support for PHY-driver SFP cages with the genphy code. On top of that, it was found by sashiko that running sfp_bus_add_upstream() for genphy deadlocks, as for genphy the PHY probing runs under RTNL, which isn't the case for non-genphy drivers. This problem was reproduced, and does lead to a deadlock on RTNL. Before the blamed commit, the phy_sfp_probe() call was made by individual PHY drivers, so there was no way to get to the SFP probing path when using genphy. Let's therefore only run phy_sfp_probe when not using genphy.
In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Fix slab-out-of-bounds in mlx5_query_nic_vport_mac_list mlx5_query_nic_vport_mac_list() sizes its firmware command buffer using the PF's log_max_current_uc/mc_list capabilities. When querying a VF vport with a larger configured max (via devlink), the firmware response can overflow this buffer: BUG: KASAN: slab-out-of-bounds in mlx5_query_nic_vport_mac_list+0x453/0x4c0 [mlx5_core] Read of size 4 at addr ff1100013ffc8a12 by task kworker/u96:2/385 CPU: 12 UID: 0 PID: 385 Comm: kworker/u96:2 Not tainted 7.0.0-rc6+ #1 PREEMPT Hardware name: QEMU Standard PC (Q35 + ICH9, 2009) Workqueue: mlx5_esw_wq esw_vport_change_handler [mlx5_core] Call Trace: <TASK> dump_stack_lvl+0x69/0xa0 print_report+0x176/0x4e4 kasan_report+0xc8/0x100 mlx5_query_nic_vport_mac_list+0x453/0x4c0 [mlx5_core] esw_update_vport_addr_list+0x2e3/0xda0 [mlx5_core] esw_vport_change_handle_locked+0xa1f/0x1060 [mlx5_core] esw_vport_change_handler+0x6a/0x90 [mlx5_core] process_one_work+0x87f/0x15e0 worker_thread+0x62b/0x1020 kthread+0x375/0x490 ret_from_fork+0x4dc/0x810 ret_from_fork_asm+0x11/0x20 </TASK> Fix by querying the vport's own HCA caps to size the buffer correctly. Refactor the function to allocate and return the MAC list internally, removing the caller's dependency on knowing the correct max.
In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: xsk: Fix DMA and xdp_frame leak on XDP_TX xmit failure In the XSK branch of mlx5e_xmit_xdp_buff(), when sq->xmit_xdp_frame() returns false (e.g. XDPSQ is full), the function returns without unmapping the DMA address or freeing the xdp_frame allocated by xdp_convert_zc_to_xdp_frame(). The xdpi_fifo push only happens on success, so the completion path cannot recover these entries. With CONFIG_DMA_API_DEBUG=y, the leak surfaces on driver unbind: DMA-API: pci 0000:08:00.0: device driver has pending DMA allocations while released from device [count=1116] One of leaked entries details: [device address=0x000000010ffd7028] [size=1534 bytes] [mapped with DMA_TO_DEVICE] [mapped as phy] WARNING: kernel/dma/debug.c:881 at dma_debug_device_change+0x127/0x180 ... DMA-API: Mapped at: debug_dma_map_phys+0x4b/0xd0 dma_map_phys+0xfd/0x2d0 mlx5e_xdp_handle+0x5ae/0xac0 [mlx5_core] mlx5e_xsk_skb_from_cqe_mpwrq_linear+0xc4/0x170 [mlx5_core] mlx5e_handle_rx_cqe_mpwrq+0xc1/0x290 [mlx5_core] Add the missing unmap + xdp_return_frame, matching the cleanup already done in mlx5e_xdp_xmit(). has_frags is rejected earlier in this branch, so no per-frag unmap is needed.
In the Linux kernel, the following vulnerability has been resolved: ipv6: sit: reload inner IPv6 header after GSO offloads ipip6_tunnel_xmit() caches the inner IPv6 header pointer at function entry and continues using it after iptunnel_handle_offloads(). For GSO skbs, iptunnel_handle_offloads() calls skb_header_unclone(). When the skb header is cloned, skb_header_unclone() can call pskb_expand_head(), which may move the skb head. The pskb_expand_head() contract requires pointers into the skb header to be reloaded after the call. If the later skb_realloc_headroom() branch is not taken, SIT uses the stale iph6 pointer to read the inner hop limit and DS field. That can read from a freed skb head after the old head's remaining clone is released. Reload iph6 after the offload helper succeeds and before subsequent reads from the inner IPv6 header. Keep the existing reload after skb_realloc_headroom(), since that branch can also replace the skb.
In the Linux kernel, the following vulnerability has been resolved: net: openvswitch: fix possible kfree_skb of ERR_PTR After the patch in the "Fixes" tag, the allocation of the "reply" skb can happen either before or after locking the ovs_mutex. However, error cleanups still follow the classical reversed order, assuming "reply" is allocated before locking: it is freed after unlocking. If "reply" allocation happens after locking the mutex and it fails, "reply" is left with an ERR_PTR, and execution jumps to the correspondent cleanup stage which will try to free an invalid pointer. Fix this by setting the pointer to NULL after having saved its error value.
In the Linux kernel, the following vulnerability has been resolved: gpio: rockchip: fix generic IRQ chip leak on remove The driver allocates domain generic chips using irq_alloc_domain_generic_chips() during probe. However, on driver remove/teardown, the generic chips are not automatically freed when the IRQ domain is removed because the domain flags do not include IRQ_DOMAIN_FLAG_DESTROY_GC. This causes both the domain generic chips structure and the associated generic chips to be leaked. Additionally, the generic chips remain on the global gc_list and may later be visited by generic IRQ chip suspend, resume, or shutdown callbacks after the GPIO bank has been removed, potentially resulting in a use-after-free and kernel crash. Fix the resource leak by explicitly calling irq_domain_remove_generic_chips() before removing the IRQ domain in rockchip_gpio_remove().
In the Linux kernel, the following vulnerability has been resolved: sctp: fix uninit-value in __sctp_rcv_asconf_lookup() __sctp_rcv_asconf_lookup() in net/sctp/input.c only checks that the ASCONF chunk can hold the ADDIP header and a parameter header, then calls af->from_addr_param(), which reads the full address (16 bytes for IPv6) trusting the parameter's declared length. An unauthenticated peer can send a truncated trailing ASCONF chunk that declares an IPv6 address parameter but stops after the 4-byte parameter header; reached from the no-association lookup path, from_addr_param() then reads uninitialized bytes past the parameter. Impact: an unauthenticated SCTP peer makes the receive path read up to 16 bytes of uninitialized memory past a truncated ASCONF address parameter. The sibling __sctp_rcv_init_lookup() bounds parameters with sctp_walk_params(); this path open-codes the fetch and omits the bound. Verify the whole address parameter lies within the chunk before from_addr_param() reads it, the same class of fix as commit 51e5ad549c43 ("net: sctp: fix KMSAN uninit-value in sctp_inq_pop").
In the Linux kernel, the following vulnerability has been resolved: sctp: validate embedded INIT chunk and address list lengths in cookie sctp_unpack_cookie() only checked that the embedded INIT chunk length did not exceed the remaining cookie payload, but did not ensure that the INIT chunk is large enough to contain a complete INIT header. A malformed COOKIE_ECHO can therefore carry a truncated INIT chunk whose length field is smaller than sizeof(struct sctp_init_chunk). Later, sctp_process_init() accesses INIT parameters unconditionally, which may lead to out-of-bounds reads. In addition, raw_addr_list_len is not fully validated against the remaining cookie payload. When cookie authentication is disabled, an attacker can supply an oversized raw_addr_list_len and cause sctp_raw_to_bind_addrs() to read beyond the end of the cookie. The address parser also lacks sufficient bounds checks for parameter headers and lengths, allowing malformed address parameters to trigger out-of-bounds reads. Fix this by: - requiring the embedded INIT chunk length to be at least sizeof(struct sctp_init_chunk); - validating that the INIT chunk and raw address list together fit within the cookie payload; - verifying sufficient data exists for each address parameter header and payload before parsing it. Note that sctp_verify_init() must be called after sctp_unpack_cookie() and before sctp_process_init() when cookie authentication is disabled. This will be addressed in a separate patch.
In the Linux kernel, the following vulnerability has been resolved: net: guard timestamp cmsgs to real error queue skbs skb_is_err_queue() treats PACKET_OUTGOING as the sole marker for an skb from sk_error_queue. That assumption is not true for AF_PACKET sockets: outgoing packet taps are also delivered to packet sockets with skb->pkt_type == PACKET_OUTGOING, but their skb->cb is owned by AF_PACKET instead of struct sock_exterr_skb. If such an skb is received with timestamping enabled, the generic timestamp cmsg path can read AF_PACKET control-buffer state as sock_exterr_skb::opt_stats. With SO_RXQ_OVFL enabled, the packet drop counter overlaps opt_stats. An odd drop count makes the path emit SCM_TIMESTAMPING_OPT_STATS with skb->len and skb->data. For non-linear skbs this copies past the linear head and can trigger hardened usercopy or disclose adjacent heap contents. Keep skb_is_err_queue() local to net/socket.c, but make it verify that the PACKET_OUTGOING marker is paired with the sock_rmem_free destructor installed by sock_queue_err_skb(). AF_PACKET receive skbs use normal receive ownership and no longer pass as error-queue skbs, while legitimate sk_error_queue entries keep the PACKET_OUTGOING marker and sock_rmem_free ownership.
In the Linux kernel, the following vulnerability has been resolved: ptp: ocp: fix resource freeing order Commit a60fc3294a37 ("ptp: rework ptp_clock_unregister() to disable events") added a call to ptp_disable_all_events() which changes the configuration of pins if they support EXTTS events. In ptp_ocp_detach() pins resources are freed before ptp_clock_unregister() and it leads to use-after-free during driver removal. Fix it by changing the order of free/unregister calls. To avoid irq handler running on the other core while ptp device unregistering, call synchronize_irq() after HW is configured to stop producing irqs and no irqs are in-flight.
In the Linux kernel, the following vulnerability has been resolved: ip6_vti: fix incorrect tunnel matching in vti6_tnl_lookup() In vti6_tnl_lookup(), when an exact match for a tunnel fails, the code falls back to searching for wildcard tunnels: - Tunnels matching the packet's local address, with any remote address wildcard remote). - Tunnels matching the packet's remote address, with any local address (wildcard local). However, vti6 stores all these different types of tunnels in the same hash table (ip6n->tnls_r_l) prone to hash collisions. The bug is that the fallback search loops in vti6_tnl_lookup() were missing checks to ensure that the candidate tunnel actually has a wildcard address.
In the Linux kernel, the following vulnerability has been resolved: netfilter: revalidate bridge ports ebt_redirect_tg() dereferences br_port_get_rcu() return without a NULL check, causing a kernel panic when the bridge port has been removed between the original hook invocation and an NFQUEUE reinject. A mere NULL check isn't sufficient, however. As sashiko review points out userspace can not only remove the port from the bridge, it could also place the device in a different virtual device, e.g. macvlan. If this happens, we must drop the packet, there is no way for us to reinject it into the bridge path. Switch to _upper API, we don't need the bridge port structure. Also, this fix keeps another bug intact: Both nfnetlink_log and nfnetlink_queue use CONFIG_BRIDGE_NETFILTER too aggressive, which prevents certain logging features when queueing in bridge family: NETFILTER_FAMILY_BRIDGE can be enabled while the old CONFIG_BRIDGE_NETFILTER cruft is off. Fixes tag is a common ancestor, this was always broken.
In the Linux kernel, the following vulnerability has been resolved: netfilter: x_tables: avoid leaking percpu counter pointers The native and compat get-entries paths copy the fixed rule entry header from the kernelized rule blob to userspace before overwriting the entry's counter fields with a sanitized counter snapshot. On SMP kernels, entry->counters.pcnt contains the percpu allocation address used by x_tables rule counters. A caller can provide a userspace buffer that faults during the initial fixed-header copy after pcnt has been copied but before the later sanitized counter copy runs. The syscall then returns -EFAULT while leaving the raw percpu pointer in userspace. Copy only the fixed entry prefix before counters from the kernelized rule blob, then copy the sanitized counter snapshot into the counter field. Apply this ordering to the IPv4, IPv6, and ARP native and compat get-entries implementations so a fault cannot expose the internal percpu counter pointer.
In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_exthdr: fix register tracking for F_PRESENT flag nft_exthdr_init() passes user-controlled priv->len to nft_parse_register_store(), which marks that many bytes in the register bitmap as initialized. However, when NFT_EXTHDR_F_PRESENT is set, the eval paths write only 1 byte (nft_reg_store8) or 4 bytes (*dest = 0 on TCP/DCCP error path). When len > 4, registers beyond the first are never written, retaining uninitialized stack data from nft_regs. Bail out if userspace requests too much data when F_PRESENT is set.
In the Linux kernel, the following vulnerability has been resolved: net: mvpp2: sync RX data at the hardware packet offset mvpp2 programs the RX queue packet offset, so hardware writes received data at dma_addr + MVPP2_SKB_HEADROOM. The current CPU sync starts at dma_addr and only covers rx_bytes + MVPP2_MH_SIZE bytes, which syncs the unused headroom and misses the same number of bytes at the packet tail. On non-coherent DMA systems this can leave the CPU reading stale cache contents for the end of the received frame. Use dma_sync_single_range_for_cpu() with MVPP2_SKB_HEADROOM as the range offset so the sync covers the Marvell header and packet data actually written by hardware.
In the Linux kernel, the following vulnerability has been resolved: net: mvpp2: limit XDP frame size to the RX buffer mvpp2 has short and long BM pools, and short pool buffers can be smaller than PAGE_SIZE. The XDP path nevertheless initializes every xdp_buff with PAGE_SIZE as frame size. XDP helpers use frame_sz to validate tail growth and to derive the hard end of the data area. Advertising PAGE_SIZE for short buffers can let bpf_xdp_adjust_tail() grow a packet past the real allocation, corrupting memory or later tripping skb tailroom checks. Initialize the XDP buffer with bm_pool->frag_size so XDP tailroom matches the actual buffer backing the packet.
In the Linux kernel, the following vulnerability has been resolved: net: mvpp2: refill RX buffers before XDP or skb use The RX error path returns the current descriptor buffer to the hardware BM pool. That is only valid while the driver still owns the buffer. mvpp2_rx_refill() can fail after the current buffer has been handed to XDP or attached to an skb. In those cases mvpp2_run_xdp() may have recycled, redirected, or queued the page for XDP_TX, and an skb free also retires the data buffer. Returning such a buffer to BM lets hardware DMA into memory that is no longer owned by the RX ring. Refill the BM pool before handing the current buffer to XDP or to the skb. If the allocation fails there, drop the packet and return the still-owned current buffer to BM, preserving the pool depth. Once the refill succeeds, later local drops retire/free the current buffer instead of returning it to BM.
In the Linux kernel, the following vulnerability has been resolved: ipv6: Fix a potential NPD in cleanup_prefix_route() addrconf_get_prefix_route() can return the fib6_null_entry sentinel entry which has a NULL fib6_table pointer. Therefore, before setting the route's expiration time, check that we are not working with this entry, as otherwise a NPD will be triggered [1]. Note that the other callers of addrconf_get_prefix_route() are not susceptible to this bug: 1. addrconf_prefix_rcv(): Requests a route with the 'RTF_ADDRCONF | RTF_PREFIX_RT' flags which are not set on fib6_null_entry. 2. modify_prefix_route(): Fixed by commit a747e02430df ("ipv6: avoid possible NULL deref in modify_prefix_route()"). 3. __ipv6_ifa_notify(): Calls ip6_del_rt() which specifically checks for fib6_null_entry and returns an error. [1] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1] SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037] [...] Call Trace: <TASK> __kasan_check_byte (mm/kasan/common.c:573) lock_acquire.part.0 (kernel/locking/lockdep.c:5842 (discriminator 1)) _raw_spin_lock_bh (kernel/locking/spinlock.c:182 (discriminator 1)) cleanup_prefix_route (net/ipv6/addrconf.c:1280) ipv6_del_addr (net/ipv6/addrconf.c:1342) inet6_addr_del.isra.0 (net/ipv6/addrconf.c:3119) inet6_rtm_deladdr (net/ipv6/addrconf.c:4812) rtnetlink_rcv_msg (net/core/rtnetlink.c:6997) netlink_rcv_skb (net/netlink/af_netlink.c:2555) netlink_unicast (net/netlink/af_netlink.c:1344) netlink_sendmsg (net/netlink/af_netlink.c:1899) __sock_sendmsg (net/socket.c:802 (discriminator 4)) ____sys_sendmsg (net/socket.c:2698) ___sys_sendmsg (net/socket.c:2752) __sys_sendmsg (net/socket.c:2784) do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
In the Linux kernel, the following vulnerability has been resolved: drm/vc4: fix krealloc() memory leak Don't just overwrite the original pointer passed to krealloc() with its return value without checking latter: MEM = krealloc(MEM, SZ, GFP); If krealloc() returns NULL, that erases the pointer to the still allocated memory, hence leaks this memory. Instead, use a temporary variable, check it's not NULL and only then assign it to the original pointer: TMP = krealloc(MEM, SZ, GFP); if (!TMP) return; MEM = TMP; While on it, use krealloc_array().
In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_tunnel: fix use-after-free on object destroy nft_tunnel_obj_destroy() calls metadata_dst_free() which directly kfree()s the metadata_dst, ignoring the dst_entry refcount. Packets that took a reference via dst_hold() in nft_tunnel_obj_eval() and are still queued (e.g. in a netem qdisc) are left with a dangling pointer. When these packets are eventually dequeued, dst_release() operates on freed memory. Replace metadata_dst_free() with dst_release() so the metadata_dst is freed only after all references are dropped. The dst subsystem already handles metadata_dst cleanup in dst_destroy() when DST_METADATA is set.
In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_meta_bridge: fix stale stack leak via IIFHWADDR register NFT_META_BRI_IIFHWADDR declares its destination register with len = ETH_ALEN (6 bytes), which the register-init tracking rounds up to two 32-bit registers (8 bytes). nft_meta_bridge_get_eval() then does memcpy(dest, br_dev->dev_addr, ETH_ALEN), writing only 6 bytes and leaving the upper 2 bytes of the second register as uninitialised nft_do_chain() stack. A downstream load of that register span leaks those stale bytes to userspace. Zero the second register before the memcpy so the full declared span is written.
In the Linux kernel, the following vulnerability has been resolved: tee: shm: fix shm leak in register_shm_helper() register_shm_helper() allocates shm before calling iov_iter_npages(). If iov_iter_npages() returns 0, the function jumps to err_ctx_put and leaks shm. This can be triggered by TEE_IOC_SHM_REGISTER with struct tee_ioctl_shm_register_data where length is 0. Jump to err_free_shm instead.
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sync: reject oversized Broadcast Announcement prepend Existing advertising instances can already hold the maximum extended advertising payload. When hci_adv_bcast_annoucement() prepends the Broadcast Announcement service data to that payload, the combined data may no longer fit in the temporary buffer used to rebuild the advertising data. Reject that case before copying the existing payload and report the failure through the device log. This keeps the existing advertising data intact and avoids overrunning the temporary buffer.
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: L2CAP: reject BR/EDR signaling packets over MTUsig net/bluetooth/l2cap_core.c:l2cap_sig_channel() accepts BR/EDR signaling packets up to the channel MTU and dispatches each command without enforcing the signaling MTU (MTUsig). A Bluetooth BR/EDR peer within radio range can send a fixed-channel CID 0x0001 packet that is larger than MTUsig and contains many L2CAP_ECHO_REQ commands before pairing. In a real-radio stock-kernel run, one 681-byte signaling packet containing 168 zero-length ECHO_REQ commands made the target transmit 168 ECHO_RSP frames over about 220 ms. Impact: a Bluetooth BR/EDR peer within radio range, before pairing, can force 168 ECHO_RSP frames from one 681-byte fixed-channel signaling packet containing packed ECHO_REQ commands. Define Linux's BR/EDR signaling MTU as the spec minimum of 48 bytes and reject any larger signaling packet with one L2CAP_COMMAND_REJECT_RSP carrying L2CAP_REJ_MTU_EXCEEDED before any command is dispatched. The Bluetooth Core spec wording for MTUExceeded says the reject identifier shall match the first request command in the packet, and that packets containing only responses shall be silently discarded. Linux intentionally deviates from that prescription: silently discarding desynchronizes the peer because the remote stack never learns its responses were dropped, and locating the first request command requires walking command headers past MTUsig, i.e. processing bytes from a packet we have already decided is too large to process. We therefore always emit one reject and use the identifier from the first command header, a single fixed-offset byte read. The unrestricted BR/EDR signaling parser and ECHO_REQ response path both trace to the initial git import; no later introducing commit is available for a Fixes tag.